考虑行走弹性影响下的车辆换挡过程分析

为研究行走弹性对工程车辆行走换挡过程的影响，建立了考虑驱动轮轮胎变形引起的车辆行走弹性影响的整车行走动力学模型，该模型适用于换挡过程分析。计算与分析了典型装载机动力换挡过程，将考虑或不考虑行走弹性时计算得到的整车加速度和瞬时冲击度的变化过程分别进行了对比，利用实车试验对单一换挡过程进行了验证；并将考虑行走弹性时升挡过程中变速箱输入输出转速变化过程、离合器滑摩功率特性的计算结果与不考虑行走弹性时换挡过程的计算结果进行了对比。研究结果表明：与不考虑行走弹性的情况相比，行走弹性变形使得换挡过程中整车加速度的变化更加平缓；换入挡离合器有两次滑摩过程，冲击度更小，换挡时间更长；离合器接合时的冲击度与其接入时间有关；滑摩功更小。     

废旧锂电池正极材料回收技术研究进展

介绍了当前国内外三种车用锂电池正极材料的回收技术,包括火法冶金技术、湿法冶金技术和生物冶金技术。经过比较,以酸浸出—沉淀/萃取法为工艺流程的湿法技术对设备和能耗要求低、浸出效率高,是工业上方便引入的一种优异技术。     

硫酸铵法利用中低品位锂瓷土矿制备碳酸锂技术研究

针对江西宜丰地区氧化锂质量分数<2.0%以下中低品位锂瓷土矿,研究了硫酸铵法提取碳酸锂技术路线。首先,利用二步焙烧工艺,有利于脱氟、提高锂浸出率,并且能够有效防止结窑现象发生。在浸出液除杂过程中,采用成矾除铝的方法将大量溶出的铝离子转变为KAl（SO₄）₂·12H₂O、NH₄Al（SO₄）₂·12H₂O等有价值复盐,规避了传统石膏法产生的大量固废,有70%的铝离子被转变为矾盐晶体,同时带出大量的结晶水,减轻后续浓缩压力,对比传统的石膏法产生大量固废而言,其优点是显而易见的。碳化反应产品的XRD以及氧化锂含量分析表明,碳酸锂的纯度达到99%以上,全程锂收率为50%~60%。作为提锂实验对比,采用宜春414矿锂质量分数为4.0%的锂云母,由于414矿样中铝的相对含量更低,导致相同的除杂难度下得到的414矿样中浸出液锂离子浓度更高,浓缩倍数更小,414矿样的锂回收率更高。实验结果表明,中低品位锂瓷土提锂的工艺规律,通过适当改变参数,能够应用于难度更低的高品位的锂云母提锂过程。     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

[数据驱动的产品设计]基于功能模型和层次分析法的智能产品服务系统概念方案构建

为研究智能产品服务系统概念方案的构建，解决系统的复杂特性和功能耦合特性，提出应用发明问题解决理论（TRIZ）功能模型和层次分析法(AHP)两种工具，在概念设计阶段利用TRIZ功能模型定性地对其进行分析建模，并借助层次分析法对不同服务供应商所提供的服务功能模块进行定量的决策分析，通过择优集成相关功能模块，形成智能产品服务系统概念方案的构建方法。最后以3家服务供应商的服务功能模块构建为例，验证该方法的有效性。     

汽车涂装废水处理技术的研究进展

汽车涂装中产生大量的工业废水，主要包括脱脂废水、磷化废水、电泳废水和喷漆废水等,其典型污染物为重金属离子、表面活性剂、油漆颗粒、磷酸盐等，是一类复杂及难处理的高浓度工业废水。依据废水中所含污染物的不同，对涂装各工序废水进行分质预处理可有效地去除磷酸盐、重金属离子、悬浮固体、油类物质等污染物，有利于减轻后续生物或高级处理单元的负荷，提高整个处理系统的效率。本文综述近年来汽车涂装废水处理方面的研究成果或实践，旨在总结预处理工艺及主体处理工艺的优点及存在的不足，希望为汽车涂装废水处理达标排放及循环回用提供一些借鉴。     

Synthesis of hexacelsian barium aluminosilicate by film boiling chemical vapour process

An original oxide/oxide ceramic-matrix composite containing mullite-based fibers and a barium aluminosilicate matrix has been synthesized by the film boiling chemical vapour infiltration process. Alkoxides were used as liquid precursors for aluminum, silicon and barium oxides. The structure and microstructure of the oxide matrix were characterized by Scanning Electron Microscopy, Energy Dispersive Spectroscopy and X-ray diffraction. Apart from small residual mullite and amorphous phase amounts, the oxide matrix is composed of the hexacelsian phase, conferring to the material interesting perspectives for high-temperature electromagnetic and structural applications.     

前置除磷优化及对多级缺氧一好氧工艺的影响

为强化厌氧-多级缺氧-好氧(A-MAO)工艺,满足GB 3838-2002的地表IV水体要求,本研究对FeCl3、Fe2(SO4)3和聚合硫酸铁(PFS)3种铁盐前置化学除磷对TP、COD的去除效果和产泥量进行研究,并考察了前置化学除磷与A-MAO工艺耦合投加量。结果表明,FeCl3和Fe2(SO4)3对TP和SS去除可达到地表IV水体要求,并明显好于PFS;FeCl3对COD的去除和产泥量最多;与FeCl3相比,Fe2(SO4)3具有较好的COD保存能力,且产泥量少。AMAO工艺使用Fe2(SO4)3前置化学除磷,导致TN含量不达GB 18918-2002要求,优化的化学生物除磷耦合投加量为130 mg/L。     

Preparation of In-doped Y2O3 ceramics through a sol-gel process: Effects on the structural and electronic properties

The Pechini-type sol-gel (PSG) process has been used for the preparation of doped oxides due to its capability to overcome most of the difficulties that frequently occur by using other producing methods. In this work we analyze the case of samples of pure and In-doped yttria (Y₂O₃) prepared by the PSG process. We experimentally characterize the synthesized samples by x-ray diffraction, micro-Raman spectroscopy, electrochemical impedance spectroscopy (EIS), and time-differential perturbed γ-γ angular correlation (PAC) spectroscopy, and we compare these results with those obtained starting from commercial oxide powders. We found that the PSG process can be used to successfully produce doped yttria in the cubic phase, with the impurities substitutionally located at the cationic sites of the structure. By the proposed PSG route, the inclusion of impurities does not affect the particle size nor the resistivity. However, when we compare the PSG samples with other samples produced from commercial powder, we found that the first have lower resistivities at grain interiors. On the other hand, PAC spectroscopy in ¹¹¹In(→¹¹¹Cd)-doped yttria allows the study of the dynamic hyperfine interactions observed by the radioactive ¹¹¹Cd impurity-probe, which can be used to “sense” the host electron availability near the impurities after the electron-capture decay of ¹¹¹In. Differences between PAC spectra for PSG samples and the commercial powder suggest that the PSG process introduces additional donor defects into the yttria electronic structure, which is consistent with the lower resistivity observed in the PSG samples by EIS spectroscopy.     

Self-lubrication and wear-resistance mechanism of graphene-modified coatings

To reduce the friction coefficient of WC-17Co wear-resistant coatings, Graphene oxide were used to mix with WC-17Co powder. The SEM, EDS and Raman results were used to analyze the morphology and phase composition of graphene oxide in the powder and coating obtained by plasma spraying processes. The mechanical properties of the coatings were studied by using a microhardness tester and a universal testing machine. The friction and wear properties of the coatings were studied by using a UMT-2 friction and wear tester. The results show that among the pulverization processes, the spray granulation process can achieve a stronger and more uniform adhesion of graphene oxide on the surface of WC-17Co particles, and the graphene oxide content in the coating is higher. Graphene is still embedded in the coating as transparent, thin sheets. The bonding strength is approximately 63 MPa, the hardness is approximately 931 HV0.1, and the friction coefficient of the graphene oxide coating is reduced by approximately 22% compared to that of the coating without graphene. The formation of lubrication films in the micro-area improves the self-lubrication and antiwear effects.